EYELET PLYERS: Describes a type of plyer used for punching small holes, with a round stud in one jaw and a hole in the other.
FEELER BLADE: Describes a thin blade of spring steel of an exact thickness used to measure small gaps or clearances between parts. Feeler blades usually come in sets of various thicknesses pinned together at one end to form a feeler gauge.
FEELER GAUGE: Describes a thin strip or blade of hardened steel, ground to an exact thickness, used to check clearances between parts. The thicknesses increase by 0.001 inches.
FILE: Describes either a flat or rounded tool with a rough surface of hardened steel that, when rubbed against metal, removes tiny particles of metal.
FILE HANDLE: Describes a wood or plastic handle fitted to the back end of a file.
FILTER WRENCH: Describes a wrench for used removing an oil filter.
FINISH HAMMER: Describes a pounding device used for shaping a panel after it has been brought approximately the right shape.
FINISHING STONE: Describes a fine grain stone used after the honing process to provide a smooth surface.
FLAT-BLADED SCREWDRIVER: Describes a screwdriver that has a blade at its end to fit slotted screws.
FLAT FILE: Describes a long, thin rectangular bar (like a blade) with angled grooves cut into the top and bottom of the larger sides, used to shape metal.
FLAT-NOSE PLYERS: Describes a very commonly used pair of plyers where the ends of the jaws are cut short.
FLEXIBLE DRIVE HANDLE: Describes a kind of socket drive tool with a pivoting head used with sockets, whose length provides excellent leverage and access to difficult locations that to it flexible ability.
FUNNEL: Describes a cup-shaped object tapering at the bottom to a small hole and a spout used to pour oil, fuel or water into relatively small openings.
GASKET PUNCH: Describes a tool used to cut out holes in a gasket sheet to shape.
GASKET SCRAPER: Describes a scraper with a sharp chisel edge used to remove old gasket material from a surface before applying a new gasket.
G-CLAMP: Describes a screw-activated clamping device in the shape of the letter "G."
GENERAL PURPOSE PLIERS: Describes any variety of typical multi-purpose pliers.
GIRDER SPANNER: Describes an adjustable wrench whose jaws are positioned at right angles to the handle.
GREASE GUN: Describes a small, hand-operated pump loaded with grease and used for lubricating the grease fittings on a vehicle.
GREASE NIPPLE: Describes a small, one-way valve used to inject grease into a bearing.
GRIP WRENCH: Describes a set of locking pliers.
GROOVING HAMMER: Describes a wide-nose peen hammer.
HACKSAW: Describes a tool used for cutting metal, with a narrow blade attached to a frame.
HALF-MOON SLIP JOINT PLIERS: Describes a set of multiple-slip joint plyers with a groove joint.
HALF-ROUND BODY FILE: Describes a body file with a domed file surface for working reverse-crowned panels.
HALF-ROUND FILE: Describes a file that's flat on one side and convex on the other.
HAMMER: Describes a hand tool with a metal head and a handle used to force one item against or through another.
HAND FILE: Describes a flat file used for shaping metal, with a rectangular cross-section, constant blade width, and smooth edge.
HEAVY-DUTY DIAGONAL CUTTING PLYERS: Describes diagonal cutting plyers with a special joint and handle design to provide extra cutting power.
HEAVY-DUTY END CUTTING PLIERS: Describes end cutting plyers with a special joint and handle design to provide extra cutting power,
HEAVY-DUTY RING WRENCH: Describes a very strong single end box wrench for use with a tubular handle that can be used with or without the handle to attach nuts quickly or final tightening or reaching otherwise inaccessible nuts.
HEXAGONAL BOLSTER: Describes a tool that allows a screwdriver to be turned with a wrench for extra torque to loosen tight screws.
HEXAGON KEY: Describes a key for hexagon recess screws, 90° offset at one end, better known as an Allen key.
HIGH LEVERAGE DIAGONAL CUTTING PLYERS: Describes diagonal cutting plyers with special joint and handle design to provide extra cutting power.
HIGH LEVERAGE END CUTTING PLIERS: Describes end cutting plyers with special joint and handle design to provide extra cutting power.
HOLLOWING BLOCK: Describes a custom shaped wooden block on which the desired shape can be produced by hammering.
- Home Page
- Tools and Equipment
Tools and EquipmentBack
- Site Map
- Contact Us